The electric carving machine SEM 612 has been designed for carving, for restoration works as well as for finishing statues, artistic objects and furniture, because of its robustness and its reduced vibrations.

 

The motor is driven by a foot pedal rheostat with 5 speeds ranging from 6.000 to 12.000 RPM. You can easily adjust the speed according to need.
It carves from 6.000 to 12.000 strokes per minute and is fitted with a 1.700 mm long flexible shaft. Its stainless steel sheath, reinforced with a wear-resistant steel substrate, with a high speed steel inner part. You can easily take the carving unit off and insert a rotating handle, which is standard equipped with a 6 mm collet. Further collets of diameter ø 2,35 - ø3 - 3,2, ø4 mm are available on request. (see page 5).
We suggest you to use quite big rotating files at a speed of 10.000 RPM, because small diameters would require a still higher speed.
220V monophase motor, with an effective power output of 450W. Characterists of the flexible shaft: 1.700 mm long, supplied with a 6 mm spring collet (spring collet of 2,35 – 3 – 3,2 and 4 mm diameter are available on request, see page 5).
Big advantage! This machine is used with the same gouges of pneumatic chisel “DAN 96”, but remember that on the electric carving machine you can use gouges up to a max. size of 12 mm.

 

Technical table

Article	3019
Motor power	450 W
Voltage	230 V
Min. Speed	5000 giri/1'
Max. Speed	12000 giri/1'
N. variator	5
Flexible length	1700 mm

 

Cylindrical rotating file are blade for flexible shaft, they are specific to work at high speed, in fact the hard metal files are not affected by the strong increase in temperature and abrasion of the material, so guaranteeing a long period of honorable service.

 

Thick pitch Tg 1: These rotating files are suitable for high-speed workings on wood, plastics and light alloys. They allow a max. speed of rotation ranging from 30.000 RPM (Ø 12 mm) to 45.000 RPM (Ø 4 mm).
Thin pitch Tg 3: These rotating files are suitable for working on iron, hardened and alloyed steel and can also be used for finishings on wood. They allow a max. speed of rotation ranging from 20.000 RPM (Ø 12 mm) to 30.000 RPM (Ø 4 mm).
Cross-pitch Tg 4: These rotating files are particularly suitable for finishings on steel and weld seams. They allow you to keep the working well under control, because they pulverize the shavings. They allow a max. speed of rotation of 20.000 RPM (Ø 10 mm) to 25.000 RPM (Ø 6 mm).

 

 

 

 

Rotating file with round head Ø 6 in hard metal for flexible shaft and SEM 612.

 

Cylindrical rotating file are blade for flexible shaft, they are specific to work at high speed, in fact the hard metal files are not affected by the strong increase in temperature and abrasion of the material, so guaranteeing a long period of honorable service.

 

Thick pitch Tg 1: These rotating files are suitable for high-speed workings on wood, plastics and light alloys. They allow a max. speed of rotation ranging from 30.000 RPM (Ø 12 mm) to 45.000 RPM (Ø 4 mm).
Thin pitch Tg 3: These rotating files are suitable for working on iron, hardened and alloyed steel and can also be used for finishings on wood. They allow a max. speed of rotation ranging from 20.000 RPM (Ø 12 mm) to 30.000 RPM (Ø 4 mm).
Cross-pitch Tg 4: These rotating files are particularly suitable for finishings on steel and weld seams. They allow you to keep the working well under control, because they pulverize the shavings. They allow a max. speed of rotation of 20.000 RPM (Ø 10 mm) to 25.000 RPM (Ø 6 mm).

 

 

	ht	Lt	G.	Art.	Size	Tg.
6	18	50	6	1594	2	1
8	18	63	6	1596	3	1
10	20	65	6	1598	4	1
12	25	70	6	1600	5	1
4	14	50	6	1593	1	3
6	18	50	6	1595	2	3
8	18	63	6	1597	3	3
10	20	65	6	1599	4	3
12	25	70	6	1601	5	3
6	18	50	6	1644	2	4
10	20	65	6	1645	4	4

 

 

 

 

 

 

 

 

 

 

Rotating files for flexible shafts

Ogival rotating file with round head Ø 6 in hard metal for flexible shaft and SEM 612.

Cylindrical rotating file are blade for flexible shaft, they are specific to work at high speed, in fact the hard metal files are not affected by the strong increase in temperature and abrasion of the material, so guaranteeing a long period of honorable service.

 

Thick pitch Tg 1: These rotating files are suitable for high-speed workings on wood, plastics and light alloys. They allow a max. speed of rotation ranging from 30.000 RPM (Ø 12 mm) to 45.000 RPM (Ø 4 mm).
Thin pitch Tg 3: These rotating files are suitable for working on iron, hardened and alloyed steel and can also be used for finishings on wood. They allow a max. speed of rotation ranging from 20.000 RPM (Ø 12 mm) to 30.000 RPM (Ø 4 mm).
Cross-pitch Tg 4: These rotating files are particularly suitable for finishings on steel and weld seams. They allow you to keep the working well under control, because they pulverize the shavings. They allow a max. speed of rotation of 20.000 RPM (Ø 10 mm) to 25.000 RPM (Ø 6 mm).

Technical table

 

Rotating files for flexible shafts

Dovetail rotating file with frontal cutting edge with round head Ø 6 in hard metal for flexible shaft and SEM 612.

Cylindrical rotating file are blade for flexible shaft, they are specific to work at high speed, in fact the hard metal files are not affected by the strong increase in temperature and abrasion of the material, so guaranteeing a long period of honorable service.

 

Thick pitch Tg 1: These rotating files are suitable for high-speed workings on wood, plastics and light alloys. They allow a max. speed of rotation ranging from 30.000 RPM (Ø 12 mm) to 45.000 RPM (Ø 4 mm).
Thin pitch Tg 3: These rotating files are suitable for working on iron, hardened and alloyed steel and can also be used for finishings on wood. They allow a max. speed of rotation ranging from 20.000 RPM (Ø 12 mm) to 30.000 RPM (Ø 4 mm).
Cross-pitch Tg 4: These rotating files are particularly suitable for finishings on steel and weld seams. They allow you to keep the working well under control, because they pulverize the shavings. They allow a max. speed of rotation of 20.000 RPM (Ø 10 mm) to 25.000 RPM (Ø 6 mm).

Rotating files for flexible shafts

Coned rotating file with round head Ø 6 in hard metal for flexible shaft and SEM 612.

 

Cylindrical rotating file are blade for flexible shaft, they are specific to work at high speed, in fact the hard metal files are not affected by the strong increase in temperature and abrasion of the material, so guaranteeing a long period of honorable service.

Thick pitch Tg 1: These rotating files are suitable for high-speed workings on wood, plastics and light alloys. They allow a max. speed of rotation ranging from 30.000 RPM (Ø 12 mm) to 45.000 RPM (Ø 4 mm).
Thin pitch Tg 3: These rotating files are suitable for working on iron, hardened and alloyed steel and can also be used for finishings on wood. They allow a max. speed of rotation ranging from 20.000 RPM (Ø 12 mm) to 30.000 RPM (Ø 4 mm).
Cross-pitch Tg 4: These rotating files are particularly suitable for finishings on steel and weld seams. They allow you to keep the working well under control, because they pulverize the shavings. They allow a max. speed of rotation of 20.000 RPM (Ø 10 mm) to 25.000 RPM (Ø 6 mm).

 

Technical table

 

Rotating files for flexible shafts

Flame rotating file with round head Ø 6 in hard metal for flexible shaft and SEM 612.

Cylindrical rotating file are blade for flexible shaft, they are specific to work at high speed, in fact the hard metal files are not affected by the strong increase in temperature and abrasion of the material, so guaranteeing a long period of honorable service.

 

Thick pitch Tg 1: These rotating files are suitable for high-speed workings on wood, plastics and light alloys. They allow a max. speed of rotation ranging from 30.000 RPM (Ø 12 mm) to 45.000 RPM (Ø 4 mm).

Thin pitch Tg 3: These rotating files are suitable for working on iron, hardened and alloyed steel and can also be used for finishings on wood. They allow a max. speed of rotation ranging from 20.000 RPM (Ø 12 mm) to 30.000 RPM (Ø 4 mm).
Cross-pitch Tg 4: These rotating files are particularly suitable for finishings on steel and weld seams. They allow you to keep the working well under control, because they pulverize the shavings. They allow a max. speed of rotation of 20.000 RPM (Ø 10 mm) to 25.000 RPM (Ø 6 mm).